Wohoo, you've found our USA website.
Click here for the ULTIMATE SAUSAGE MAKING GUIDE & Product Usage Instructions.

This section doesn’t currently include any content. Add content to this section using the sidebar.

Image caption appears here

Add your deal, information or promotional text

How to use our casings

Sausage making made simple

Whether you’re new to the craft or an experienced hand, it’s always good to keep up with a few tips and tricks when it comes to sausage making so we’ve given Luke (the owner of The New Zealand Casings Co) a bit of a spruce up and set him loose in front of the camera to do what he loves to do best – making great tasting sausages using our 100% natural sausage casings. Make sure you listen right to the end to hear his number 1 tip.

Using our casings

Follow these instructions to get the best results when using our sausage casings.

1. Rinse your casings.

It is essential to rinse all visible salt off the casings. Do this by running the casing under the tap using cold water. Try to massage between the folds. Do not remove the casing from the tube provided.

2. Soak your casings.

Once rinsed, you must soak your casings in fresh, warm water, ideally 99°F. (which is your body temperature). Make sure they are fully submerged and avoid water any hotter than 104°F. Soak your casings for at least 45 minutes. Alternatively, casings can be soaked overnight in cold tap water.

3. Get the right sized nozzle.

Different sized casings need a different sized sausage maker nozzle (also known as funnel, stuffing tube or stuffing horn), otherwise you may cause tears in your casing. Sheep casings require a smaller nozzle than hog casings. We strongly recommend the following nozzle sizes:
- Sheep 19-21mm = 10-13mm / 0.4-0.5" nozzle
- Sheep 24-26mm = 13-16mm / 0.5-0.5" nozzle
- Hog 32-35mm = 19-25mm / 0.75-1" nozzle
The measurements are the diameter of the stuffing horn at its tip.

4. Thread your casing onto the nozzle.

Our casings have been threaded onto either a soft or hard tubes for easier use. To thread casings onto your nozzle, follow these instructions:


Hard Tubes:
1. Wet the sausage filling horn /nozzle with water or dab and spread a small amount of vegetable oil on the nozzle and spread over.
2. Remove the casing and tube from the water.
3. Slide the casing tube onto the piping nozzle. If you have the right sized nozzle it should fit inside the casing tube.
4. Slide the casing off the casing tube onto the sausage making nozzle. 
5. Spread the casing out evenly along the nozzle.
6. Pull ~10cm / 3-4" of casing off the end and tie a knot in the end of the casing. You are ready to start filling.

Soft Tubes:
1. Wet the sausage filling horn /nozzle with water or dab and spread a small amount of vegetable oil on the nozzle and spread over.
2. Remove the casing and tube from the water.
3. Thread the casing tube onto the piping nozzle so that all of the casing is on the nozzle. It is ok if some of the tube is hanging off the end of the nozzle. Thread the folded end of the tube on first.
4. Gently hold the casing on the stuffing horn with one hand. With the other hand, hold onto the folded end of the tube and gently pull it out, pulling away from the sausage stuffing horn.
5. Spread the casing out evenly along the nozzle.
6. Pull ~10cm / 3-4" of casing off the end and tie a knot in the end of the casing. You are ready to start filling.

Storage instructions

Our sausage casings are dry salted for preservation. They will last for at least 12 months as long as you follow the three golden rules:

1. Keep salted.

If you have left-over casing and have washed the salt off then remove any excess water by running your fingers down the casings then generously re-coat with any finely ground table salt (not rock salt or flaked salt). The easiest way to do this is to put your casing in a bowl and sprinkle a generous amount of salt over it, then roll the casing around in the salt. The salt will stick to the residual moisture on the casing. You want the casing to be completely covered in salt. More salt is better than not enough so if in doubt add more, excess salt will not harm the product.

2. Keep air tight.

Wrap in clingfilm/gladwrap and put back into the pouch packaging provided or into a container.

3. Keep cool.

Store your sausage casings in a cool, temperature-controlled environment of between 5°C and 10°C – ideally in the fridge. Store casings away  from direct sunlight and heat at all times. We do not recommend freezing your casings.

Search